100円ラジオの基板を使用した3球レフレックススーパー
2004年6月完成

3 tubes reflex super het using PWB of 100Yen radio
Completed   June. 2004 

100YENPWBFRONT3.JPG - 27,391BYTES 

大きさ:57mmx33mmx118mm(つまみ部除く)
   Size : 2.2"x1.3"x4.6"(except protrusion of knob)         

特徴:      ・100円ラジオのプリント基板を利用したレフレックス3球スーパー  
         (100円ラジオの基板上の部品は一旦全て取り去った後、
               レフレックス3球スーパーの回路を、その基「板」上に構成)
   ・部品も大半は100円ラジオのものを使用                        
・外装、機構部品も大半100円ショップで入手             
     ・4球スーパ相当の感度。スピーカも内蔵                         

      Features :                                                                               
*Reflex 3-tubes superhet using PWB of 100Yen radio.            
               (All parts on PWB of 100Yen radio were once removed, and thereafter, 
                 circuit of reflex 3-tubes superhet was constructed on the "board". )
*Most of its parts are also get from 100Yen radio.                  
              *Materials for case or mechanical structure are obtained at 100Yen shop.
          *About the same sensitivity with standard 4-tubes portable super het.

 100YENPWBBACK.JPG - 22,334BYTES  100YENPWB2.JPG - 15,410BYTES    
裏側                                         基板パタン面側           
Back side                                  PWB pattern side             


  100YENPWB3.JPG - 19,017BYTES
基板の比較。 左;100円ラジオ、右;本機
Comparison of PWB;  left; original 100Yen radio, right; this radio.


使用球    : 5678 x3                                                                           
Tube line up : 5678 x3                                                                            


回路構成:周波数変換 中間周波増幅  検波     電圧増幅    電力増幅
          5678     5678    ダイオード   5678      5678
                          ※電圧増幅はレフレックスでIFと共用

    Block diagram: Converter    IF-AMP      2nd-Detector   AF-AMP       Power AMP
                       5678         5678             diode          5678             5678
                                   *AF and IF are amplified in 1 tube using reflex circuit

 

製作動機、方針:
これまで100円ラジオの部品を使ったラジオをいくつか作りましたが、「無線家のラジオ」として、真空管式のポケットラジオをもっと簡単に作れないものかとの考えから、100円ラジオのプリント基板もそのまま利用できないものかとと考えました。
製作方針は下記のようにしました。
   1、100円ラジオのプリント基板を利用し、箔カット、ジャンパは最小限に抑える。
   2、100円ラジオの部品を最大限利用し、その他の部品もなるべく100円ショップで入手する。
       3、「ガチャポンカプセル3球レフレックススーパー」同様、球は5678ばかり3本のみ使用する。

Motive for making this radio and policies
I've made some radios using parts of 100Yen radio. And as a radio of "Musenka", I wanted to make tube pocket portable radio more easily. And I thought of utilizing of PWB of 100Yen radio as well as its parts on it.
 I planned with the policies listed below.
      1,Utilize PWB of 100Yen radio. And number of cutting its pattern and jumper wire will be minimized. 
      2,Utilize also parts of 100Yen radio and also obtain the other parts at 100Yen shop as many as I can.
      3,Tubes to be used are 3 tubes and all are 5678 as with "Gachapon capsule 3 tubes reflex super het".


回路図
※回路図はあくまで参考です。利用は自由としますが利用により生じるいかなる結果にも責任を負いません。

Schematic
*Schematic is only a reference and can be use freely  But I  can't be responsible for any result.

100YENPWB.GIF - 11,956BYTES

100YENPWB1.JPG - 68,310BYTES
基板上の部品配置 ; オリジナルCR類の配置とシルク印刷は無視され、回路図上の部品がこのように再配置されています。
Parts arrangement on PWB ; Original arrangement and silk printing of C,R, are ignored                                               
                             and parts on schematic are rearranged like this.

回路について:
  R5とC5が追加されているほかは「ガチャポンカプセル3球レフレックススーパー」と全く同じです。球は5678のみを3本使用し、IFTは2箇所共単同調で、レフレックスのAF負荷はボリウムの抵抗を使用という特徴も同じです。このため100円ラジオの主要部品を過不足なく利用できています。
  R5はIF−AMPにかかるAGC電圧を分圧し、AGCによる感度低下を少なくしています。C5はAF信号のバイパス用です。このようにすると感度はやや良くなるのですがレフレックス特有のAFの発振を起こす場合があるので注意が必要です。「ガチャポンカプセル3球レフレックススーパー」では実際に発振を起こしたのでR5とC5は入れていません。
About schematic:
Schematic diagram is almost the same with "Gachapon capsule 3-tubes reflex super het" except C5 and R5. It uses three tubes, and all tubes are 5678. IFTs of input side and output side of IF-AMP are both single tuned type. AF load of reflex circuit is substituted with resistor of volume control. These features are also all the same with "Gachapon capsule 3 tubes reflex super het".  Thus Most of main parts of 100Yen radio can be used.
R5 divide AGC voltage applied to IF-AMP, and limit the effect of AGC and improve sensitivity. C5 is bypass for AF. With this circuit arrangement, sensitivity will be rather improved. But be careful because in some case, it cause harmful AF oscillation peculiar in reflex circuit. Actually, in case of "Gachapon capsule 3 tubes reflex super het" it cause harmful AF oscillation in reflex circuit, and I had to omit it.



     電池: ・A電池:単3x1 1.5V
          ・B電池:23A 12Vx4個 48V
                               
          Batteries requirement:
                     
*A-batteries : AA-cell x 1  1.5V
                      *B-batteries : 23A   12Vx4   48V


     使用部品:・主要部品は球、出力トランス、スピーカ以外は
                            100円ラジオのものを使用。コイル類の巻線は変更。
            ・出力トランス−−ST30(相当品)の改造(巻線の変更)。
                          ・スピーカは100円ショップの小型スピーカボックスのもの。
         
          Parts:       *Main parts except tubes, output trans and speaker
                           are taken out from 100Yen radio.
                         *Output transformer--Remake of ST-30 (equivalent type)
                         *Speaker is out from small speaker box of 100Yen shop. 


      外装   :1.4mm厚の透明アクリル板で自作。アクリル板は100円ショップで入手 
   
          Casing      : Hand made, made of clear acryl plate thickness of 1.4mm.
                           This acryl plate was obtained at 100Yen shop.


         シャーシ :金属製のシャーシはなし。100円ラジオのプリント基板を使用
  
           Chassis    : Using PWB of 100Yen radio, has no metal chassis

          つまみ類 :100円ラジオのもの
   
           Knobs       :Knobs of 100Yen radio.


外装、構造 :
  大半の電子部品は100円ラジオの基板に取り付けられています。バリコン、OSCコイル、IFT、バーアンテナはオリジナルの100円ラジオと同じ位置に取り付けられています。ボリウムはオリジナルの丁度裏側(パタン面側)に移動し、空いたスペースに出力トランスを配置しています。
  基板の部品面側には球を配置するスペースがどうしても取れなかったので、球はパタン面側のバリコンのつまみの上に配置しました。配線の都合で周波数変換管だけ向きが逆になっています。
  中間周波増幅管(と出力管)のコーティングをはがしたので、中間周波増幅管の周囲には薄い銅板のシールドが設けられています。
   そして、前面板に、この基板、スピーカ、電池ホルダを含む全ての部品が取り付けられ、後方から箱型をしたカバーをかぶせるような構造になっています。
  電池ホルダ、外装は1.4mm厚の透明アクリル板で作られています。このアクリル板も100円ショップで入手しました。
  ボリウムとバリコンのつまみがケースの両サイドから出なければならないので、ケースの幅は小さな100円ラジオの基板の幅に合わせる必要があります。このため高さに比べ幅が狭い形状になっています。

Casing and mechanical structure: 
Most of electronic parts are fixed onto PWB of 100Yen radio. Variable capacitor, oscillator coil, IFTs and stick antenna are arranged to same position with original 100Yen radio. Volume control was moved to just opposite side of PWB(pattern side). And output transformer is arranged to the space where volume control was arranged in original 100Yen radio.
Tubes are arranged on knob of tuning capacitor on pattern side, since I could not find out space to arrange tubes on parts side. 
Only converter tube is fixed upside-down, because of convenience of wiring. 
I stripped off the shield coating of IF-AMP tube (and POWER AMP tube). And so, there is a shield plate made of thin copper plate around IF-AMP tube. 
All parts including this PWB, loud speaker, batteries holder are fixed on to front plate. And cover this body with box shaped back cover.
Casing and batteries holder are made of clear acryl plate thickness of 1.4mm. This acryl plate was also obtained from 100Yen shop.
Knobs of volume and tuning capacitor should protrude from each sides of casing. and width of casing should be determined by width of small PWB of 100Yen radio. And so, The width of casing became narrow relative to its height.

 100YENPWBCHASSIS.JPG - 20,536BYTES  
全ての部品が取り付けられる前面板。 電池ホルダはスピーカのマグネットヨークに取付られています。
Front plate to which all parts are fitted. Batteries holder is fitted on to magnet yoke of speaker.

性能、他  :
  内蔵のバーアンテナのみで鉄筋の室内で当地(大阪府寝屋川市)の地元局は全て受信でき、同条件で夜間は遠距離局も受信でき、感度は意外と良く、動作も安定です。また、音量もポケットラジオとしては実用レベルです。しかし、ボリウムが低周波増幅の後に入っているので強電界で音が歪みやすい傾向があります。
  ポケットラジオとしては縦長で、やや変な形状ですが、球が正面から見えるのは面白い点です。
「無銭家のラジオ」としての出来栄え:球と出力トランス以外の大半の回路部品と外装用のアクリル板は100円ショップで集めることができ、このため球以外の部品代は650円程でした。球も5678ばかりなので、入手は容易です。
  100円ラジオの基板は箔カットとジャンパそれぞれ3箇所程で、ほとんどそのまま使用できましたので、コイル類の巻きなおしが終わると回路部分の製作はほとんどキット感覚でした。
  このラジオはケースをどうするか考える前に回路基板が完成しました。回路基板の製作に手間がかからなかったのでケースも手間をかけずに作りたいと思い、既製品のケースで適当なものがないか探したのですがみつからず、結局、ケースは誂え品になってしまったのは不満な点です。
   実はこのラジオが完成した少し後に100円ラジオが100円ショップから消えてしまい、掲載すべきかどうか悩んだのですが、100円ラジオはかなり話題になり、また気軽に買えたのでラジオ作りを趣味とされる方は大概、今でも2〜3個は持っておられると考え、敢えて掲載することにしました。

Performance and others :
All stations within about 30 miles can be received with built-in stick antenna in my home (ferroconcrete structure). And at night some distant station can be received. Sensitivity is unexpectedly good, and stable. And volume of sound is level of practical use as pocket a radio. But sound tend to distort when input signal is large, because volume control is put after AF-AMP.
This radio became rather odd "tall boy" as a pocket radio. But It is attractive that all tubes can be seen from front of this radio.
Execution as a radio of "Musenka": I could obtain acryl plate for casing and most of its parts except tubes and output tras, at 100Yen shop. So, all parts except tubes could be obtained at price of  about 650Yen (about US$ 6.2) . And also tubes are easy to obtain, since all tubes are 5678.
PWB of 100Yen radio was used almost as it was, except about 3 points of pattern cutting and 3 jumper wires. And so, after I finish to convert coils and transformers, I made its circuit with feeling of making kit.    
Circuit on PWB of this radio was completed effortlessly before I planned its casing . And I wanted to make casing also effortlessly. And I looked for suitable ready made case, but I could not find out such a case. So, I had to make custom made casing after all. It is a point of dissatisfaction.
To tell the truth, I was irresolute it was proper to be posted on my web or not, since soon after it was completed, 100Yen radio disappeared in 100Yen shop. But I think most of radio amateur (sorry, only in Japan) have 2 or 3 100Yen radio even now, since 100Yen radio was very popular and easy to obtain. And so, I decided to post it on my web.

戻る

Back