大きさ:100mmx65mmx33mm(つまみ部除く)
Size : 3.9"x2.6"x1.3"(except
protrusion of knob)
特徴:
暗いところでは1S5のフィラメントが光るのが見えます
In the dark, orange glow of
filament of 1S5 can be seen.
使用球 : 1S5
3S4
Tube line up :
1S5 3S4
回路構成: 検波 電圧増幅 電力増幅
1S5(D)
1S5(P)
3S4
Block diagram:
Detector AF-AMP Power
AMP
1S5(D)
1S5(P)
3S4
製作動機、方針:
ギターアンプの一種にスモーキーアンプというポケットサイズのアンプがあるそうで、当ホームページのラジオに似た感じの大きさ、形なので、真空管式のスモーキーアンプというものを作ってみることにしました。
しかし、残念ながら私はエレキギターを弾かないので、スモーキーアンプというよりは、イヤホン式ラジオをスピーカで聞くためのアンプ、またはシグナルトレーサとして作ることにしました。
Motive for
making this radio and policies
:
Recently, I know about
Smokey AMP that is a kind of guitar AMP and is pocket size. It is similar
size and appearance with radios posted on my WEB. And so, I tried to make
tube type smokey AMP.
But unfortunately, I can't play guitar. So,
I planned to make it as AF-AMP for hearing earphone type radio (like crystal
radio) with loud speaker, or make it as signal tracer rather than Smokey
AMP.
回路図
Schematic
※回路図はあくまで参考です。利用は自由としますが利用により生じるいかなる結果にも責任を負いません。
*Schematic is only a reference
and can be use freely But I can't be responsible for any result.
回路について:
回路は、標準的な電池式4球スーパの低周波部分とほとんど同じです。電圧増幅に使用した1S5は2極管部があるので、これを有効に利用したかったので、シグナルトレーサの検波回路に使っています。入力信号のタイプ(RFまたはAF)はSW1で切り替えます。
About schematic:
Schematic is almost the same with AF
section of standard Battery operated 4-tube superhet.
I used 1S5 for AF-AMP.
1S5 has diode section, I wanted to use it effectively. And so I used it as
detector for signal tracer. The type (RF or AF) of input is selected with
SW1.
電池: ・A電池:単3x2 1.5V
・B電池:23A 12Vx4個 48V
Batteries
requirement:
*A-batteries : AA-cell x 2
1.5V
*B-batteries : 23A 12Vx4 48V
使用部品:・主要部品はトランジスタ用を使用。
・出力トランス−−ST30(相当品)の改造(巻線の変更)。
・S付VR 500KΩ スイッチ1回路1接点をそのまま使用
Parts: *Main parts are
parts are parts for transistor
radio.
*Output transformer--Remake of ST-30 (equivalent
type)
*Volume control--500kohms originally have 1 switch, I use it as it
is.
外装 :既存の透明プラスチックケースを使用
Casing : Ready-made clear plastic case
シャーシ :1mm厚のアルミ板で自作
Chassis : Hand
made, with aluminum plate thickness of
1mm.
つまみ類 :既製品
Knobs :Ready-made
articles.
外装、構造 :
電池ホルダは1.4mm厚のアクリル板で作られており、アルミ板のシャーシが、この電池ホルダの上に取り付けられています。真空管(のソケット)と、主要な部品はこのシャーシに取り付けられています。ボリウムと入力ジャックはケースに取り付けられています。
Casing and mechanical
structure:
Batteries holder is made of acryl plate
thickness of 1.4mm. and chassis made of aluminum plate is attached on the
batteries holder. Tubes (sockets) and main electronic parts are attached to
this aluminum plate. Volume control and jack for input are fixed to case.
.
電池ホルダと、アルミシャーシに組まれた回路
Batteries holder and circuit made onto aluminum
chassis.
戻る
Back